BN-Series
General Features
The BN-35 is a low cost pin for pin functional replacement for the Newport model 215, with many more features. It is a 3 1/2 digit voltmeter in a compact 96x24mm case with non-isolated 5VDC power. Another version of the BN-35, the BN-35I with internally isolated 9V, 12V, 15V or 24VDC power, is also available.
The case has a short depth of just 2.83 inches (72mm) behind the panel.
The meter has four user-selectable ranges of 200mV, 2V, 20V and 200V. The BN-35 may also be calibrated at the factory for these ranges or specially scaled for other ranges (see Ordering Information below). Provision to offset the zero is also available as an option for 4-20mA signals.
DC Volts Single-ended measurement
DC Volts
Ratiometric Voltmeter with external reference.
5V DC
5V DC
For using the BN-35 as a ratiometric voltmeter with an external reference, open J8 and close J9 jumpers.
Meter display =
x 1000
If Signal Low is common to the 5VDC Power Ground, remove resistor R307 and replace it with a jumper (i.e. short the resistor R307).
The BN-Series have a matching DIN case style that is complementary to the Lynx, Leopard and Tiger family of meters. BN-Meters are the OEMs choice for economical switchboard and process indication. For economy, each model is dedicated to a specific application and designed for quick and easy installation.
1/8
Specifications
Input Configuration:.......True differential
Full Scale Ranges:.........199.9mVDC 1.999VDC (standard)
19.99VDC199.9VDC
Input Impedance:............Exceeds 100M on 200mV, 2V ranges.
1M other ranges.
Input Protection:.............100V AC/DC for 200mV, 2V and 20V
ranges. 250VAC/DC for 200V range
Conversion Rate:.............3 readings per second
Common Mode Rejection:...80dB at DC
Normal Mode Rejection:......60dB at 50/60Hz for 200mV and 2V ranges.
Common Mode Voltage:..-1V to +2VDC
Accuracy:........................ (0.05% of reading + 1 digit)
Temperature Coefficient:....5ppm/ C in ratiometric mode 50ppm/ C in
200mV / 2V ranges
Maximum resolution:......100V in 200mV range.
Zero Stability:...................Autozeroed. 0.1 counts per C
Display:.............................0.56" high red LEDs. Display Hold, Blank
and Test provided.
Overrange Indication:.....The most significant digit "1" is displayed
with all the other digits blanked.
Power Supply:..................5VDC @ 200mA.
Operating Temperature:..0C to 60C
Storage Temperature:......-40C to 85C
Relative humidity:............95% (non condensing)
Case Dimensions:...........Bezel: 96X24 mm (3.62 X 0.95)
Depth behind bezel: 56.5 mm (2.23) Plus 27 mm (1.06) for Push-On connector or plus 17.5 mm (0.68) for Edge connector
Weight:..............................85 gms (3 oz)
125 gms (4.4 oz) when packed
BN-Series, For Those Applications Where Space Is A Premium
BN-35...........0.2/2/20/200V DC ranges, 3.5 digit, 5V DC Powered BN-35BCD.......Parallel or Multiplex BCD, 3.5 digit, 5V DC Powered BN-35CL........4 to 20mA, Isolated 24V DC, 3.5 digit BN-35I..........0.2/2/20/200V DC ranges, Isolated 24V DC, 3.5 digit
BN-40BCD.......Parallel or Multiplex BCD, 4.0 digit, 5V DC Powered BN-45...........2/20/200V DC ranges, 4.5 digit, 5V DC Powered BN-45I..........2/20/200V DC ranges, Isolated 24V DC, 3.5 digit
The model BN-35 interconnects by means of a standard PC board edge connector having two rows of 15 pins, spaced on 0.156" centers. Texmate also offers a Push-On screw terminal connector that provides a great advantage in ease-of-use (see pg. four). Connectors are available from Texmate.
Rear View of Meter
power is connected to these pins. The standard BN-35 is designed to be powered from a 5VDC supply. Other power supply options are also available. See page three.
Pin 6 - External Reference Input: See page three for operating the meter with an external reference as a ratiometric voltmeter.
Pin 7 - Hold/Test/Blank Common Pin: The Display Hold/Test/Blank pins have to be connected to this pin to be activated.
Pin H - Display Blank/Dim: If this pin is connected to Pin 7, the display will be blanked out. If a 5K potentiometer is connected between this pin and Pin 7, the brightness of the display may be smoothly adjusted.
Pins 8 and J - Display Test: These pins are internally connected together. All numeric display segments will light up when these pins are connected to the Hold/Test Blank Common Pin 7.
Pins 9 and K - Signal High Input: These pins are internally connected together. Signal high input for the meter. The input voltage can range from200mV to 200VDC. By closing some solder jumpers, the user can change from one range to another.
See page three for range change information.
Pins 10 and L - Signal Low Input: These pins are internally connected together. Signal low input of the A/D Converter.
Pins 11 and M - Reserved Pins: These pins have been reserved for future new functions. Please do not use them as tie points for external wiring, as they are connected to internal circuit points.
Pins 12 & N, 13 & P and 14 & R - Decimal Points: These are the decimal point pins. Connecting any of these pins to the Decimal Select Common Pin makes that particular decimal point come on.
Pins 15 and S - Decimal Select Common: These pins are internally connected together. The decimal point pins must be connected to this pin to come on.
Zero Pot
Span Pot
R307
Pins 1 & A - Positive DC Power Input: These pins are internally connected together. The positive end of the DC power is connected to these pins. The standard BN-35 meter is designed to be powered from a 5VDC power supply. Other power supplies options are available. See page three. Before using the meter, make sure that the appropriate power is being applied.
Pins 2 & B - Hold Reading: These pins are internally connected together. If these pins are left unconnected, the meter will operate in a free-running mode. When these pins are connected to the Hold/Test/Blank Common Pin 7, the meter will latch up.
A/D conversions will continue, but the display will not be updated until Pins 2 & B are disconnected from Pin 7.
Pins 3, 4, C, and D - Negative DC Power Input: These pins are internally connected together. The negative end of the DC
J1 J2
SOLDER SIDE
BN-35 Data Sheet(BN01)
SPAN Potentiometer (Pot)
The 15 turn SPAN pot is always on the right side (as viewed from the front of the meter). Typical adjustment is 20% of the input signal range.
The BN-35 ships from the factory with a non-isolated 5VDC power supply. For applications where isolation is required between the power and signal grounds, use the Texmate model BN-35I. This model is available with 9V, 12V, 15V, and 24V power options and generates an internally isolated supply.
ZERO Potentiometer (Pot)
The Optional ZERO pot when installed is always to the right of the SPAN pot (as viewed from the front of the meter). Typically it enables the displayed reading to be offset 1000 counts.
Changing the range to 200mV, 20V or 200V. The BN-35 comes standard as a 2VDC meter. The factory can recalibrate the meter to a different range either when the meter is ordered or as an after sale service using part number VRC-DPM.
For the user to change the range, closing of some jumpers by soldering and opening other jumpers is required. Follow the chart below to achieve the required range. See the above component layout to find location of jumpers. Remember to recalibrate the meter after every range change.
Input Range
Open Jumper
Closed Jumper
200mV
J1 and J2
J3 and J4
20V
200V
J1, J2, J3 and J4
J1, J3, J4
J2, J3, J4
The BN-35 is calibrated at the factory with a precision DC voltage source. Whenever the range is changed, the meter needs to be recalibrated. The Span Potentiometer is accessible with the front cover of the meter removed for user calibration.
1. Make sure there is proper DC power and input.
2. Connect the power supply.
3. Apply a positive signal input equal to 95% of the full scale
input.
4. Adjust Span Potentiometer in the front of the meter so that
the displayed reading agrees with the signal input.
5. The BN-35 is now calibrated and ready for use.
Unscrew the knurled collars, and remove the mounting clips.
Snap out the rear plastic plate. The BN-35 printed circuit board can then be easily removed by sliding it out from the rear of the case.
To customize the front bezel, each BN-meter is supplied with a white printed clear adhesive label containing popular
descriptors. Choose the descriptor desired, peel off the adhesive backing and align the descriptor in the center right of the faceplate.
various
They provide the greatest convenience and ease of use Texmates exclusive optional Push-On Connectors combine an edge card connector and a 10 position screw terminal block. Push-On Connectors are ordered preconfigured for each specific power supply voltage and each optional power supply available for the BN-Series.
PCB Edge Connector
A standard 30-pin edge connector (two rows of 15 pins on 0.156" centers) may be used to connect the BN-35 meter. Order part no. CN-L15.
Texmate Produces Thousands of Custom OEM Face Plates
Have Texmate Design and Build a Custom Face Plate to Suit your Next project!
Custom face plates have a nonrecurring artwork charge. A serial number is then assigned to each artwork, to facilitate re-ordering.
Small Run or One-Off custom face plates incur an installation charge, and are generally printed on a special plastic film, which is then laminated to custom faceplate blanks as required.
Large Run (250 pieces min): custom face plates are production silk screened, issued a part number, and held in stock for free installation as required by customer orders.
OEMs may also order Custom Meter Labels, Box Labels
Custom Data Sheets and Instruction Manuals.
FRONT VIEW
SIDE VIEW
TO REMOVE REAR COVER
When extra panel mounting tightness is required, optional Screw Mounting Clips are included which fit on the Mounting Slide Clips.
Various bezel colors are available. Black is standard.
The 96x24mm case is particularly suitable for mounting in mosaic panels or insulative panels. They can also stack mount, 2 up in existing cut-outs for 1/8 DIN (96x48mm) or 4 up in 1/4 DIN (96x96mm).
Standard Options for this Model Number
Description
STANDARD.......Red LEDs, 0.56 inch high BN-GREEN.......Green LED, 0.56 inch high BN-BRIGHT.......Super bright Red LEDs, 0.56 inch high
Special Options and Accessories
Description
Part Number
(cid:2)SPECIAL OPTIONS (Specify Inputs & Req. Reading) HD-CHANGE.........Range change from the standard input as shown in BOLD type V0-50K..........Zero offset potentiometer 50k VRC-DPM........Range change for BN-35/BN-35I listed ranges CB-FS35.........Non-Std Range and Scale Changes, 3.5 Digit Meters (cid:2)ACCESSORIES
CN-L15..........PCB Edge Connector, Solder Type, Dual Row 15 Pins CN-PUSH/BN.....BN Series Push-on Screw Terminal Block Connector 75-DMTC96X24...Side Slide Brackets, extra set (96x24mm only) 75-DBBZ96X24..Black Bezel for 96x24mm Case, BN and AM series DN.CAS96X24...Din Case 96 X 24 Short Depth with Bezel
For product details visit www.texmate.com
Local Distributor Address
995 Park Center Drive Vista, CA 92081-8397
Tel: 1-760-598-9899 USA 1-800-839-6283 Thats 1-800-TEXMATE Fax: 1-760-598-9828 Email: [email protected] Web: www.texmate.com
BN-35 Data Sheet(BN01)
Texmate is an American manufacturer of high durability industrial grade panel meters, bar graphs, and transducers. Texmate's meters are frequently equipped with relays and various signal outputs for industrial automation applications and are known for their extremely long service life.